QUICK OVERVIEW
Displays the current gear number
Shows the current gear from 1 to a maximum of 6 as well as a neutral display.
Automatic programming
Compatible with all motorcycles, four-wheelers, bicycles, etc., everything fits with a gear lever
The red illuminated display is automatically dimmed at night.
Detects current gear faster than other gear displays that use a speedometer / tachometer signal.
The display can be mounted anywhere
Description:
Condition:100% Brand New
Item Name:Speed Gear Display Indicator
Size:4cm*4cm*4cm/1.57inch*1.57inch*1.57inch
Feature:
Shows current gear number
Indicates current gear from 1 to max of 6. as well as a neutral indicator.
Auto programming
Compatible with all motorbikes,four wheeler,bikes etc. will fit anything with a shift lever
Red illuminated display will automatically dim at night.
Detects the current gear faster than other gear indicators that use speedometer/tachometer signal.
Display can be mounted anywhere
Foreword:
Congratulations on your purchase of a Jxkj gear position indicator. is the most advanced gear position indicator on the market today. This product will fit all Suzuki fuel injected (FI)motorcycles which have on-board Diagnostic System connector.This connector is referred as "Mode select switch coupler" in the Suzuki manuals. Unlike other gear indicators available for your bike,this product connects to the diagnostic connector. It makes the installation very simple.The unit reads data directly from the ECM, offering faster and more reliable readings than competitive products.The unit is fully automatic,there are no buttons and no "programming wire", The display will indicate all gears correctly when ignition is On,side stand is UP and the engine stop switch is in RUN position.
Installation:
Find the WHITE,6-pole male diagnostic connector,usually near the ECM box.It may have a black cap,or "dummy" female plug (without wires) attached to it.GSF650 Bandit/GSF1250;under right side frame cover DL650 ABS model;behind right side fuel tank cover VL1500/Boulevard C90/Intruder C1500;behind left frame head cover Other models;under seat (rider or pillion) Remove the black cap or dummy female plug,and connect the Jxkj plug.Route the cable to the mounting location.Peel off the green plastic from the back of the unit,and mount the display.Secure the cable with the cable ties supplied.The unit is fully functional after installation.there is no need to setup. Troubleshooting.
Disconnect the Jxkj connector and check whether the pins are broken,bent or pushed out of position.Reconnect the plug, and make sure that all connections are good and the connector is fully seated.Make sure the ignition is ON,side stand is UP and engine stop switch is in RUN position when you test the gear position indicator.If some gears are not indicated properly,most likely the Gear Position switch is defective,modified,or a TRE box is installed.If the indicated gears are correct except under hard acceleration or braking,there is interference in the bike is wiring and the ECM receives incorrect gear position values from the sensor.This Jxkj model indicates the gear position as known by the ECM.
Fitment:
For Boulevard C50 2005-2008
For Boulevard M50 2005-2018
For Boulevard C90 2005-2012
For Boulevard C109R/T 2008-2015
For Boulevard M109R/R2 2006-2010
For DL650 V-Strom 2004-2011
For DL1000 V-Strom 2004-2013
For GSF650 Bandit 2007-2008
For GSF1250 N/NA Bandit 2007-2009
For GSF1250 S/SA Bandit 2007-2016
For GSX1400 2004-2009
For GSX-R600 2004-2005
For GSX-R750 2004-2005
For GSX-R1000 2003-2004
For Intruder C800 2005-2008
For Intruder M800 2005-2015
For Intruder C1500 2005-2012
For Intruder M1500 2009-2015
For Intruder C1800R 2008-2015
For Intruder M1800R 2006-2010
For RMX-450Z All Years
For RM-Z250 (Fi model) All Years
For RM-Z450 (Fi model) All Years
For SV650 2003-2014
For SV1000 2003-2009
For VL800 Intruder Volusia 2005-2008
For VL1500 Intruder 2005-2012
For VLR1800 2008-2015
For VZ800 Marauder 2005-2015
For VZ1500 2009-2015
For VZR1800 2006-2010
CHF
